Jump to content
DottieD

Powrtouch Problem

Recommended Posts

I've got an original Powrtouch motor mover on my 2008 Eccles Topaz.

It did not work or have a handset controller when I bought the van.

I had an engineer test the system and it turned out that the main control box wasn't working.

I've fitted a refurbished control box which came with a hand controller.

The system all operates correctly now, apart from one of the actual drive motors which works fine when disengaged, but stalls when engaged.

The other motor works fine.

I'm thinking it's possibly brushes in the motor?

Anyone else had a similar problem?

Share this post


Link to post
Share on other sites

I would tend to agree with your diagnosis, I don’t think the brushes are very expensive.

Might be worth checking all the connections in case one isn’t as good as it should be. 

 

Andy 

Edited by Mr Plodd

Share this post


Link to post
Share on other sites

The wear on the brushes should be pretty even on both motors so it seems odd that one motor would need them and not the other.

I think the wires are attached to the brushes using push fit spade connectors which can work loose, a poor connection will also cause the motor to stall.

Share this post


Link to post
Share on other sites

if the drive motors work fine when off the wheel , have you checked the gap is correct and also the tyres are pumped up correctly

Share this post


Link to post
Share on other sites
14 minutes ago, joanie said:

if the drive motors work fine when off the wheel , have you checked the gap is correct and also the tyres are pumped up correctly

 

Did you miss the below in the original post??

 

apart from one of the actual drive motors which works fine when disengaged, but stalls when engaged.

 

Andy

Share this post


Link to post
Share on other sites
25 minutes ago, Mr Plodd said:

 

Did you miss the below in the original post??

 

apart from one of the actual drive motors which works fine when disengaged, but stalls when engaged.

 

Andy

 

Actually Joanie makes a valid point, if the gap is too small between the tyre and the motor when it is engaged the motor could press too hard on the tyre and cause it to stall, so no I don't think she missed that at all!

  • Thanks 1

Share this post


Link to post
Share on other sites

I agree with Andy and Steve. If you examine the terminal connectors on the motor you may find a very bad connection  (dirty/corroded/loose, then carefully slide out the bushes dont loose the loose retainer plate. You can easily see whether the bushes are worn out. Powertouch sell replacements. They also sell the rubber covers for the motor which tend to rot away in the elements. When re-assembling the rubber covers, a cable tie will ensure that no water and dirt can enter in the future. The other possibility of the failure is poor connections at the controller end of the same cable. These motors need alll the voltage from a good 12v battery or they will not perform well.

Share this post


Link to post
Share on other sites

Can we assume the caravan wheels are free to rotate on both sides and there is no binding brake or other issue that causes the stall?  My old PowrTouch model 1 would cut-out/stall at the drop of a 1 inch kerb sometimes ;) 

 

Get a reel of self-amalgamating tape rather than the PowrTouch boots to wrap around the motor and spade terminal connections.  It will be cheaper, and more effective in my opinion.

 

PowrTouch have the instructions on how to and it would be worth removing the brushes to check them on both sides for comparison purposes or in case both motor sides could be better  replaced. https://www.powrtouch.com/powrwheel-support-hub-html/previous-generation-mover-support/powrtouch-model-1-support.html 

Share this post


Link to post
Share on other sites

Thanks for all of your replies.

The wheels on the van turn freely, I've already checked the roller gap and its got brand new tyres which are correctly inflated.

I'll check the connectors and brushes next time we are allowed out. :(

Share this post


Link to post
Share on other sites

Swap over the connections at the control box between left and right, try it again, if the fault stays on the same side it's the motor or the wiring, if the fault moves it's the control box. I would seriously doubt brushes, movers get so little use but pretty much equal between left and right, brushes would also tend to give intermittent operation rather than lack of power. 

Edited by AJGalaxy2012

Share this post


Link to post
Share on other sites

I replaced the brushes on my mover. The brushes didn't look too worn but the springs had lost a fair bit of their spring if you get my meaning. I did this because drive on one motor was sometimes intermittent. All sorted now.

Share this post


Link to post
Share on other sites

Roller bearing  worn, partially seized ?

Share this post


Link to post
Share on other sites

2016 auto engage powrtouch on s/a van.

Whilst on subject, aside, can anyone advise .....

All operating fine but when my units are in the parked / de-powered / dormant position the roller units can be rattled around by hand and cause a metal to metal knocking noise - normal ? 

Thanks

Share this post


Link to post
Share on other sites
37 minutes ago, montesa said:

2016 auto engage powrtouch on s/a van.

Whilst on subject, aside, can anyone advise .....

All operating fine but when my units are in the parked / de-powered / dormant position the roller units can be rattled around by hand and cause a metal to metal knocking noise - normal ? 

Thanks

Yes on my 4wd system.

 

Ian

Share this post


Link to post
Share on other sites

A friend has a similar problem it turn out to be the battery? Try and borrow a good battery or as we did if you can get your car close we ran jump leads from the car to the caravan battery. We tried this mostly as it was suggested by the guy at power touch.

Share this post


Link to post
Share on other sites
15 minutes ago, PaulR said:

A friend has a similar problem it turn out to be the battery? Try and borrow a good battery or as we did if you can get your car close we ran jump leads from the car to the caravan battery. We tried this mostly as it was suggested by the guy at power touch.

Its a brand new,  fully charged 110 aH battery which is trickle charged by a small solar panel when in storage.

Battery voltage was 12.78v last time I checked it.

Share this post


Link to post
Share on other sites

Fingers crossed you get to the bottom of it. I'll be interested to the answers.

Share this post


Link to post
Share on other sites

why don't you get back in touch with the engineer and  ask him ?

Share this post


Link to post
Share on other sites
2 hours ago, IanV8 said:

Yes on my 4wd system.

 

Ian

 

Normal situation or the same problem ?

Share this post


Link to post
Share on other sites

×
×
  • Create New...