Search the Community
Showing results for tags 'removal'.
Found 11 results
-
I have a Lunar Venus 540/4 and the microwave has ceased to function. Electrical supply checks out, fuse is ok. I need to remove it from its housing but cannot see how. Can anyone help?
-
Hi. .. I have a Senator 6 and the shower valve is defective. I've got a replacement but I can see how to get the old one out. There is a white plastic cover in the corner of the shower cubical in which the valve is mounted, but I can not see how to remove it. There are no screws or clips. It seems to be a snap in type system, I'll pulled and poked but not got it off. Before I break it trying. .. can anyone explan how to remove this cover? Many thanks Mat
-
Has anybody removed the blind on a Hartal door, the spring seems to have gone and I need to remove the blind so I I can replace the spring. The model is a Swift Fairway 2013 so if somebody could go through the procedure I would be obliged and also where do I get a replacement spring.
-
Hello all, Does anyone know how to remove a drawer from the front chest in a Pegasus GT65? Thanks.
-
can anyone tell me how to remove the front and side panels on my Keswick Awning. There are 4 zips to each panel and I cannot figure out how to unzip the panels, as the zips stop the panels from being removed. I would love to know how to remove the panels having all these zips
-
We have been caravanning since the 1970 starting with a very small knowlsey two berth no hot water electrics fridge etc towing with an MGBGT!!!!! then Eccles Lunar, Compass Pentar which fell to bits as the furniture was not screwed into a frame. ..lovely spec but. ..... I now have an Elddis Omega which has 2 large mirrors on the bathroom wall one behind the basin has de-silvered I know from previous posts that they are stuck as well as screwed but I have two chrome headed ? do these screw off or prise off I do not want to cause damage. Thank you if you can help. Many thanks Judvik
-
Avondale Harrier. Removed all fittings including plug hole, and sealant but tray will not lift out. Help. Tray very tight to all walls etc. Do not really want to destroy tray as may still reuse. Have to remove to get wall boards off to repair damp in corner.
-
The high level brake light on my Swift Challenger 560 has ceased to function. Can anyone help with how it is attached so I can remove it to check wiring etc?.
-
Need to take my Alde control panel out to get to the rear to add a remote room temperature sensor. I think the controller is screwed on but I guess the cover plate probably clips on to it. I have found the standard sensor not very useful and hope supplementing it with one in a better position will make it work better for us. Does the front of the panel clip on. It looks a bit flimy so don't want to crack or break it. Can't get to rear of unit without removing a panel (doesn't look easy) though I can feed the new sensor cable to it OK and attach it if I can get the panel out from
-
There has been a number of threads about the best pegs for hard standing and I use hard steel ones whacked in with a lump hammer. My difficulty is getting them out. I've bent quite a few tapping them this way and that trying to loosen them and am thinking I need some sort of crow bar or other long lever. Anyone got any top tips?
-
Before I start breaking stuff, I need some guidance on fitting a new tap to my Elddis Typhoon. The current one is a Whale Elite, and has a crack in the base. To access under it I'll need to get the sink out, or I can get to it from via the outer upper fridge grill (if a heat shield can be removed). The sink is held in by a rubber seal, and the only visable screw is in the plug hole. The heat shield at the back of the fidge seems to get clipped together, though it's not clear if it can be removed from the outside. As the current tap has split I'm keen to look at fitting a metal one instea
